View NX3L4051HR-Q100_9050746.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the nx3l4051-q100 is a low-ohmic 8-channel analog switch, suitable for use as an analog or digital multiplexer/demultiplexer. the nx3l4051-q100 has three digital select inputs (s1 to s3), eight independent inputs/outputs (y0 to y7) and a common input/output (z). all eight switches share an enable input (e ). a high on e causes all switches into the high impedance off-state, independent of sn. schmitt trigger action at the digital inputs makes the circuit tolerant to slower input rise and fall times. low threshold digital inputs allows th is device to be driven by 1.8 v logic levels in 3.3 v applications without signific ant increase in supply current i cc . this makes it possible for the nx3l4051-q100 to switch 4.3 v signals with a 1.8 v digital controller, eliminating the need for logic level translation. the nx3l4051-q100 allows signals with amplitude up to v cc to be transmitted from z to yn or from yn to z. the low on resistance (0.5 ? ) and flatness (0.13 ? ), ensures minimal attenuation and distortion of transmitted signals. this product has been qualified to the automotive electronics council (aec) standard q100 (grade 1) and is suitable for use in automotive applications. 2. features and benefits ? automotive product qualif ication in accordance with aec-q100 (grade 1) ? specified from ? 40 ? c to +85 ? c and from ? 40 ? c to +125 ? c ? wide supply voltage range from 1.4 v to 4.3 v ? very low on resistance (peak): ? 1.7 ? (typical) at v cc =1.4v ? 1.0 ? (typical) at v cc =1.65v ? 0.6 ? (typical) at v cc =2.3v ? 0.5 ? (typical) at v cc =2.7v ? 0.5 ? (typical) at v cc =4.3v ? break-before-make switching ? high noise immunity ? esd protection: ? mil-std-883, method 3015 class 3a exceeds 7500 v ? hbm jesd22-a114f class 3a exceeds 7500 v ? mm jesd22-a115-a exceeds 200 v (c = 200 pf, r = 0 ? ) ? cdm aec-q100-011 revision b exceeds 1000 v ? iec61000-4-2 contact discharge exceeds 8000 v for switch ports ? cmos low-power consumption nx3l4051-q100 single low-ohmic 8-channel analog switch rev. 1 ? 7 august 2012 product data sheet
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 2 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch ? latch-up performance exceeds 100 ma per jesd 78b class ii level a ? 1.8 v control logic at v cc = 3.6 v ? control input accepts voltages above supply voltage ? very low supply current, even when input is below v cc ? high current handling capabilit y (350 ma continuous cu rrent under 3.3 v supply) 3. applications ? cell phone ? pda ? portable media player ? analog multiplexing and demultiplexing ? digital multiplexing and demultiplexing ? signal gating 4. ordering information 5. marking table 1. ordering information type number package temperature range name description version NX3L4051HR-Q100 ? 40 ? c to +125 ? c hxqfn16 plastic thermal enhanced extremely thin quad flat package; no leads; 16 terminals; body 3 ? 3 ? 0.5 mm sot1039-2 nx3l4051pw-q100 ? 40 ? c to +125 ? c tssop16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 table 2. marking codes type number marking code NX3L4051HR-Q100 m41 nx3l4051pw-q100 x3l4051
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 3 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 6. functional diagram pin numbers are shown for tssop16 package only. pi n numbers are shown for tssop16 package only. fig 1. logic symbol fig 2. functional diagram 001aal657 y7 y6 y5 y4 y3 y2 y1 y0 z e s2 11 10 6 3 4 2 5 1 12 15 14 13 s1 s3 9 001aal658 11 16 v cc 13 y0 s1 1-of-8 decoder logic 9 s3 14 y1 10 s2 6 8 gnd e 15 y2 12 y3 1y4 5y5 2y6 4y7 3z
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 4 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 7. pinning information 7.1 pinning 7.2 pin description fig 3. pin configuration sot1039-2 (hxqfn16) fig 4. pin configuration sot403-1 (tssop16) 1 2 3 4 z y7 y5 nx3l4051-q100 e 12 11 10 9 y1 y0 y3 s1 16 15 14 13 y6 y4 v cc y2 5 6 7 8 n.c. gnd s3 s2 aaa-003471 transparent top view terminal 1 index area nx3l4051-q100 y4 v cc y6 y2 zy 1 y7 y0 y5 y3 es 1 n.c. s2 gnd s3 aaa-003472 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 table 3. pin description symbol pin description sot1039-2 sot403-1 y0, y1, y2, y3, y4, y5, y6, y7 11, 12, 13, 10, 15, 3, 16, 2 13, 14, 15, 12, 1, 5, 2, 4 independent input or output z 1 3 independent output or input e 4 6 enable input (active low) n.c. 5 7 not connected gnd 6 8 ground (0 v) s1, s2, s3 9, 8, 7 11, 10, 9 select input v cc 14 16 supply voltage
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 5 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 8. functional description [1] h = high voltage level; l = low voltage level; x = don?t care. 9. limiting values [1] the minimum input voltage rating may be exceeded if the input current rating is observed. [2] the minimum and maximum switch voltage ratings may be exceeded if the switch clamping current rating is observed but may not exceed 4.6 v. [3] for hxqfn16 package: above 135 ? c the value of p tot derates linearly with 16.9 mw/k. [4] for tssop16 package: above 60 ? c the value of p tot derates linearly with 5.5 mw/k. table 4. function table [1] input channel on e s3 s2 s1 lllly0=z lllhy1=z llhly2=z l l hhy3=z lhlly4=z lhlhy5=z l hhl y6=z l hhhy7=z hxxxswitches off table 5. limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc supply voltage ? 0.5 +4.6 v v i input voltage sn and e [1] ? 0.5 +4.6 v v sw switch voltage [2] ? 0.5 v cc + 0.5 v i ik input clamping current v i < ? 0.5 v ? 50 - ma i sk switch clamping current v i < ? 0.5 v or v i >v cc + 0.5 v - ? 50 ma i sw switch current v sw > ? 0.5 v or v sw < v cc + 0.5 v; source or sink current - ? 350 ma v sw > ? 0.5 v or v sw < v cc + 0.5 v; pulsed at 1 ms duration, < 10 % duty cycle; peak current - ? 500 ma t stg storage temperature ? 65 +150 ?c p tot total power dissipation t amb = ? 40 ? cto+125 ?c hxqfn16 [3] -250mw tssop16 [4] -500mw
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 6 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 10. recommended operating conditions [1] to avoid sinking gnd current from termi nal z when switch current flows in terminal yn, the voltage drop across the bidirecti onal switch must not exceed 0.4 v. if the switch current flows into terminal z, no gnd current flows from termi nal yn. in this case, there is no limit for the voltage drop across the switch. 11. static characteristics table 6. recommended operating conditions symbol parameter conditions min max unit v cc supply voltage 1.4 4.3 v v i input voltage sn and e 04.3v v sw switch voltage [1] 0v cc v t amb ambient temperature ? 40 +125 ?c ? t/ ? v input transition rise and fall rate sn and e ; v cc = 1.4 v to 4.3 v - 200 ns/v table 7. static characteristics at recommended operating conditions; volt ages are referenced to gnd (ground 0 v). symbol parameter conditions t amb = 25 ?c t amb = ? 40 ? c to +125 ?c unit min typ max min max (85 ?c) max (125 ?c) v ih high-level input voltage v cc = 1.4 v to 1.6 v 0.9 - - 0.9 - - v v cc = 1.65 v to 1.95 v 0.9 - - 0.9 - - v v cc = 2.3 v to 2.7 v 1.1 - - 1.1 - - v v cc = 2.7 v to 3.6 v 1.3 - - 1.3 - - v v cc = 3.6 v to 4.3 v 1.4 - - 1.4 - - v v il low-level input voltage v cc = 1.4 v to 1.6 v - - 0.3 - 0.3 0.3 v v cc = 1.65 v to 1.95 v - - 0.4 - 0.4 0.3 v v cc = 2.3 v to 2.7 v - - 0.4 - 0.4 0.4 v v cc = 2.7 v to 3.6 v - - 0.5 - 0.5 0.5 v v cc = 3.6 v to 4.3 v - - 0.6 - 0.6 0.6 v i i input leakage current sn and e ; v i =gndto4.3v; v cc = 1.4 v to 4.3 v --- - ? 0.5 ? 1 ? a i s(off) off-state leakage current yn ports; see figure 5 v cc = 1.4 v to 3.6 v - - ? 5- ? 50 ? 500 na v cc = 3.6 v to 4.3 v - - ? 10 - ? 50 ? 500 na i s(on) on-state leakage current z port; v cc = 1.4 v to 3.6 v; see figure 6 v cc = 1.4 v to 3.6 v - - ? 20 - ? 200 ? 2000 na v cc = 3.6 v to 4.3 v - - ? 40 - ? 200 ? 2000 na i cc supply current v i =v cc or gnd; v sw =gndorv cc v cc = 3.6 v - - 100 - 500 5000 na v cc = 4.3 v - - 150 - 800 6000 na
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 7 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 11.1 test circuits ? i cc additional supply current v sw =gndorv cc v i = 2.6 v; v cc =4.3v - 2.0 4.0 - 7 7 ? a v i = 2.6 v; v cc = 3.6 v - 0.35 0.7 - 1 1 ? a v i = 1.8 v; v cc = 4.3 v - 7.0 10.0 - 15 15 ? a v i = 1.8 v; v cc =3.6v - 2.5 4.0 - 5 5 ? a v i = 1.8 v; v cc = 2.5 v - 50 200 - 300 500 na c i input capacitance sn and e -1.0----pf c s(off) off-state capacitance -35----pf c s(on) on-state capacitance -350----pf table 7. static characteristics ?continued at recommended operating conditions; volt ages are referenced to gnd (ground 0 v). symbol parameter conditions t amb = 25 ?c t amb = ? 40 ? c to +125 ?c unit min typ max min max (85 ?c) max (125 ?c) v i =0.3vorv cc ? 0.3 v; v o =v cc ? 0.3 v or 0.3 v. fig 5. test circuit for measuring off-state leakage current i s 001aal661 v ih v o gnd sn e z v il or v ih v cc yn v i v i =0.3vorv cc ? 0.3 v; v o =v cc ? 0.3 v or 0.3 v. fig 6. test circuit for measuring on-state leakage current 001aal662 v il v o gnd sn e z v il or v ih v cc yn v i i s
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 8 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 11.2 on resistance [1] for nx3l4051pw-q100 (tssop16 package), al l on resistance values are up to 0.05 ? higher. [2] typical values are measured at t amb = 25 ? c. [3] measured at identical v cc , temperature and input voltage. [4] flatness is defined as the difference between the maximum and minimum value of on resistance measured at identical v cc and temperature. table 8. on resistance [1] at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); for graphs see figure 8 to figure 14 . symbol parameter conditions t amb = ? 40 ? c to +85 ?c t amb = ? 40 ? c to +125 ?c unit min typ [2] max min max r on(peak) on resistance (peak) v i =gndtov cc ; i sw = 100 ma; see figure 7 v cc = 1.4 v - 1.7 3.7 - 4.1 ? v cc = 1.65 v - 1.0 1.6 - 1.7 ? v cc = 2.3 v - 0.6 0.8 - 0.9 ? v cc = 2.7 v - 0.5 0.75 - 0.9 ? v cc = 4.3 v - 0.5 0.75 - 0.9 ? ? r on on resistance mismatch between channels v i =gndtov cc ; i sw = 100 ma [3] v cc =1.4v; v sw = 0.4 v - 0.18 0.30 - 0.30 ? v cc =1.65v; v sw = 0.5 v - 0.18 0.20 - 0.30 ? v cc =2.3v; v sw = 0.7 v - 0.07 0.10 - 0.13 ? v cc =2.7v; v sw = 0.8 v - 0.07 0.10 - 0.13 ? v cc =4.3v; v sw = 0.8 v - 0.07 0.10 - 0.13 ? r on(flat) on resistance (flatness) v i =gndtov cc ; i sw = 100 ma [4] v cc = 1.4 v - 1.0 3.3 - 3.6 ? v cc = 1.65 v - 0.5 1.2 - 1.3 ? v cc = 2.3 v - 0.15 0.3 - 0.35 ? v cc = 2.7 v - 0.13 0.3 - 0.35 ? v cc = 4.3 v - 0.2 0.4 - 0.45 ?
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 9 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 11.3 on resistance t est circuit and graphs r on =v sw / i sw .( 1 ) v cc =1.5v. (2) v cc =1.8v. (3) v cc =2.5v. (4) v cc =2.7v. (5) v cc =3.3v. (6) v cc =4.3v. measured at t amb =25 ? c. fig 7. test circuit for measuring on resistance fig 8. typical on resistance as a function of input voltage v 001aal663 v il gnd sn e z v il or v ih v cc v sw yn v i i sw v i (v) 05 4 3 12 001aag564 0.8 0.4 1.2 1.6 r on () 0 (1) (2) (5) (6) (4) (3)
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 10 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch (1) t amb = 125 ? c. (2) t amb =85 ? c. (3) t amb =25 ? c. (4) t amb = ?40 ? c. (1) t amb = 125 ? c. (2) t amb =85 ? c. (3) t amb =25 ? c. (4) t amb = ?40 ? c. fig 9. on resistance as a function of input voltage; v cc =1.5v fig 10. on resistance as a function of input voltage; v cc =1.8v 001aag565 v i (v) 03 2 1 0.8 0.4 1.2 1.6 r on () 0 (1) (2) (3) (4) 001aag566 v i (v) 03 2 1 0.4 0.6 0.2 0.8 1.0 r on () 0 (1) (2) (3) (4) (1) t amb = 125 ? c. (2) t amb =85 ? c. (3) t amb =25 ? c. (4) t amb = ?40 ? c. (1) t amb = 125 ? c. (2) t amb =85 ? c. (3) t amb =25 ? c. (4) t amb = ?40 ? c. fig 11. on resistance as a function of input voltage; v cc =2.5v fig 12. on resistance as a function of input voltage; v cc =2.7v 001aag567 v i (v) 03 2 1 0.4 0.6 0.2 0.8 1.0 r on () 0 (1) (2) (3) (4) 001aag568 v i (v) 03 2 1 0.4 0.6 0.2 0.8 1.0 r on () 0 (1) (2) (3) (4)
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 11 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 12. dynamic characteristics (1) t amb = 125 ? c. (2) t amb =85 ? c. (3) t amb =25 ? c. (4) t amb = ?40 ? c. (1) t amb = 125 ? c. (2) t amb =85 ? c. (3) t amb =25 ? c. (4) t amb = ?40 ? c. fig 13. on resistance as a function of input voltage; v cc =3.3v fig 14. on resistance as a function of input voltage; v cc =4.3v v i (v) 04 3 12 001aag569 0.4 0.6 0.2 0.8 1.0 r on () 0 (1) (2) (3) (4) v i (v) 05 4 23 1 001aaj896 0.4 0.6 0.2 0.8 1.0 r on () 0 (1) (2) (3) (4) table 9. dynamic characteristics at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); for load circuit see figure 17 . symbol parameter conditions t amb = 25 ?c t amb = ? 40 ? c to +125 ?c unit min typ [1] max min max (85 ?c) max (125 ?c) t en enable time e , sn to z or yn; see figure 15 v cc = 1.4 v to 1.6 v - 45 100 - 120 125 ns v cc = 1.65 v to 1.95 v - 32 75 - 85 95 ns v cc = 2.3 v to 2.7 v - 21 50 - 55 60 ns v cc = 2.7 v to 3.6 v - 19 45 - 45 50 ns v cc = 3.6 v to 4.3 v - 19 45 - 45 50 ns t dis disable time e , sn to z or yn; see figure 15 v cc = 1.4 v to 1.6 v - 25 80 - 90 105 ns v cc = 1.65 v to 1.95 v - 15 65 - 70 75 ns v cc = 2.3 v to 2.7 v - 9 30 - 35 40 ns v cc = 2.7 v to 3.6 v - 8 25 - 30 35 ns v cc = 3.6 v to 4.3 v - 8 25 - 30 35 ns
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 12 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch [1] typical values are measured at t amb = 25 ? c and v cc = 1.5 v, 1.8 v, 2.5 v, 3.3 v and 4.3 v respectively. [2] break-before-make guaranteed by design. 12.1 waveform and test circuits t b-m break-before-make time see figure 16 [2] v cc = 1.4 v to 1.6 v - 19 - 9 - - ns v cc = 1.65 v to 1.95 v - 17 - 7 - - ns v cc = 2.3 v to 2.7 v - 12 - 4 - - ns v cc = 2.7 v to 3.6 v - 10 - 3 - - ns v cc = 3.6 v to 4.3 v - 9 - 2 - - ns table 9. dynamic characteristics ?continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); for load circuit see figure 17 . symbol parameter conditions t amb = 25 ?c t amb = ? 40 ? c to +125 ?c unit min typ [1] max min max (85 ?c) max (125 ?c) measurement points are given in table 10 . logic level: v oh is typical output voltage level that occurs with the output load. fig 15. enable and disable times 001aal664 t en t dis v x output off to high high to off output high to off off to high sn, e input v i gnd v oh v oh v m v m gnd gnd t dis t en v x v x v x table 10. measurement points supply voltage input output v cc v m v x 1.4 v to 4.3 v 0.5v cc 0.9v oh
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 13 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch a. test circuit b. input and output measurement points fig 16. test circuit for measuri ng break-before-make timing v v o 001aal665 c l r l gnd v ext = 1.5 v g v i sn e z v cc v il or v ih v il yn 001aag572 v i t b-m v o 0.9v o 0.9v o 0.5v i test data is given in table 11 . definitions test circuit: r l = load resistance. c l = load capacitance including jig and probe capacitance. v ext = external voltage for measuring switching times. v i may be connected to sn or e . fig 17. test circuit for measuring switching times v v o 001aal666 c l r l gnd v ext = 1.5 v g v i sn e z v cc v il or v ih v il yn table 11. test data supply voltage input load v cc v i t r , t f c l r l 1.4 v to 4.3 v v cc ? 2.5ns 35pf 50 ?
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 14 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 12.2 additional dynami c characteristics [1] f i is biased at 0.5v cc . 12.3 test circuits table 12. additional dynamic characteristics at recommended operating conditions; voltag es are referenced to gnd (ground = 0 v); v i = gnd or v cc (unless otherwise specified); t r = t f ? 2.5 ns; t amb = 25 ? c. symbol parameter conditions min typ max unit thd total harmonic distortion f i =20hzto20 khz; r l =32 ? ; see figure 18 [1] v cc =1.4v; v i = 1 v (p-p) - 0.15 - % v cc =1.65v; v i = 1.2 v (p-p) - 0.10 - % v cc =2.3v; v i = 1.5 v (p-p) - 0.02 - % v cc =2.7v; v i = 2 v (p-p) - 0.02 - % v cc =4.3v; v i = 2 v (p-p) - 0.02 - % f ( ? 3db) ? 3 db frequency response r l =50 ? ; see figure 19 [1] v cc = 1.4 v to 4.3 v - 15 - mhz ? iso isolation (off-state) f i = 100 khz; r l =50 ? ; see figure 20 [1] v cc = 1.4 v to 4.3 v - ? 90 - db v ct crosstalk voltage between digital inputs and switch; f i = 1 mhz; c l = 50 pf; r l =50 ? ; see figure 21 v cc = 1.4 v to 3.6 v - 0.2 - v v cc = 3.6 v to 4.3 v - 0.3 - v xtalk crosstalk between switches; f i = 100 khz; r l =50 ? ;see figure 22 [1] v cc = 1.4 v to 4.3 v - ? 90 - db q inj charge injection f i = 1 mhz; c l = 0.1 nf; r l =1 m ? ; v gen =0v; r gen =0 ? ; see figure 23 v cc = 1.5 v - 3 - pc v cc = 1.8 v - 4 - pc v cc =2.5v - 6 - pc v cc =3.3v - 9 - pc v cc =4.3v - 15 - pc fig 18. test circuit for measuri ng total harmonic distortion f i d 001aal667 r l gnd sn e z v cc 0.5v cc v il yn v il or v ih
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 15 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch adjust f i voltage to obtain 0 dbm level at output. increase f i frequency until db meter reads ? 3db. fig 19. test circuit for measuring the frequency response when channel is in on-state f i db 001aal668 r l gnd sn e z v cc 0.5v cc v il yn v il or v ih adjust f i voltage to obtain 0 dbm level at input. fig 20. test circuit for measuring isolation (off-state) f i db 001aal669 r l gnd sn e z v cc 0.5v cc r l 0.5v cc v ih yn v il or v ih
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 16 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch a. test circuit b. input and output pulse definitions fig 21. test circuit for measuring crosstalk voltage between digital inputs and switch 001aal670 r l gnd sn e z v cc 0.5v cc r l 0.5v cc yn v il or v ih v v o c l g logic input v i 001aal671 logic input (sn, e) v o v ct off off on fig 22. test circuit for measuri ng crosstalk between switches f i db 001aal672 r l gnd sn e z v cc 0.5v cc r l 0.5v cc v ih yn y0 v il or v ih
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 17 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch a. test circuit b. input and output pulse definitions definition: q inj = ? v o ? c l . ? v o = output voltage variation. r gen = generator resistance. v gen = generator voltage. v i may be connected to sn or e . fig 23. test circuit for measuring charge injection v v o 001aal673 c l r l r gen gnd v gen g v i sn e z v cc v il yn 001aal674 logic input (sn, e) v o v o off off on
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 18 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 13. package outline fig 24. package outline sot1039-2 (hxqfn16) references outline version european projection issue date iec jedec jeita sot1039-2 - - - - - - sot1039-2_po 10-07-29 11-03-30 unit mm max nom min 0.5 0.05 0.00 0.127 3.1 3.0 2.9 1.95 1.85 1.75 3.1 3.0 2.9 0.5 1.5 0.40 0.35 0.30 0.1 a dimensions hxqfn16: plastic thermal enhanced extremely thin quad flat package; no leads; 16 terminals; body 3 x 3 x 0.5 mm sot1039-2 a 1 b 0.35 0.30 0.25 cdd h ee h 1.95 1.85 1.75 ee 1 e 2 1.5 lv 0.1 w 0.05 y 0.05 y 1 0 1 2 mm scale terminal 1 index area b a d e c y c y 1 x detail x a c a 1 b e 2 e 1 e e 1/2 e 1/2 e ac b v c w terminal 1 index area d h e h l 5 8 16 13 4 1 9 12
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 19 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch fig 25. package outline sot403-1 (tssop16) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz ywv references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot403-1 mo-153 99-12-27 03-02-18 w m b p d z e 0.25 18 16 9 a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale tssop16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 a max. 1.1 pin 1 index
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 20 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 14. abbreviations 15. revision history table 13. abbreviations acronym description cdm charged device model cmos complementary metal-oxide semiconductor esd electrostatic discharge hbm human body model mm machine model pda personal digital assistant mil military table 14. revision history document id release date data sheet status change notice supersedes nx3l4051_q100 v.1 20120807 product data sheet - -
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 21 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch 16. legal information 16.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 16.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 16.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such info rmation. nxp semiconductors takes no responsibility for the content in this document if provided by an information source outside of nxp semiconductors. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use in automotive applications ? this nxp semiconductors product has been qualified for use in automotive applications. unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors and its suppliers accept no liability for inclusion and/or use of nxp semiconducto rs products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
nx3l4051_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved. product data sheet rev. 1 ? 7 august 2012 22 of 23 nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any licens e under any copyrights, patents or other industrial or intellectual property rights. export control ? this document as well as the item(s) described herein may be subject to export control regu lations. export might require a prior authorization from competent authorities. translations ? a non-english (translated) version of a document is for reference only. the english version shall prevail in case of any discrepancy between the translated and english versions. 16.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 17. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
nxp semiconductors nx3l4051-q100 single low-ohmic 8-channel analog switch ? nxp b.v. 2012. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 7 august 2012 document identifier: nx3l4051_q100 please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 18. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 7 pinning information . . . . . . . . . . . . . . . . . . . . . . 4 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 functional description . . . . . . . . . . . . . . . . . . . 5 9 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 10 recommended operating conditions. . . . . . . . 6 11 static characteristics. . . . . . . . . . . . . . . . . . . . . 6 11.1 test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 11.2 on resistance . . . . . . . . . . . . . . . . . . . . . . . . . . 8 11.3 on resistance test circuit and graphs. . . . . . . . 9 12 dynamic characteristics . . . . . . . . . . . . . . . . . 11 12.1 waveform and test circuits . . . . . . . . . . . . . . . 12 12.2 additional dynamic characteristics . . . . . . . . . 14 12.3 test circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 13 package outline . . . . . . . . . . . . . . . . . . . . . . . . 18 14 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 20 15 revision history . . . . . . . . . . . . . . . . . . . . . . . . 20 16 legal information. . . . . . . . . . . . . . . . . . . . . . . 21 16.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 21 16.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 16.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 16.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 22 17 contact information. . . . . . . . . . . . . . . . . . . . . 22 18 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

▲Up To Search▲

Price & Availability of NX3L4051HR-Q100

	To Download NX3L4051HR-Q100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .